Single Coated Tapes on Lynx Specialty Tapes


All Categories > Single Coated Tapes


	Single Coated Tapes
	Click on a category to drill down.


		LX-347(.032"): High Density Black Urethane Foam Backing: 25# per cubic foot foam density Aggressive acrylic adhesive on less compressible foam than PVC. LX-347 is a single coated black 1/32" high-density urethane foam. This product has a high performance, permanent acrylic adhesive coated on a high density, mirco-cellular open cell urethane foam carrier Note that acrylic adhesives take from 24-48 hours to cure to maximum bond strength once applied; any testing should take this into consideration. Note: Be sure surface areas are free from contamination before applying LX-347. All technical statements and recommendations contained herein are for use as general guidelines only; it is the buyer's responsibility to thoroughly test each and every product to ensure it meets his particular ...




		Light Density Black and Gray PVC Foam Backing: 7#-8# per cubic foot density foams (7) These products work well in cushioning, vibration dampening and sound dampening applications. Also used to seal out dust and insects. Foam is highly comfortable and easy to compress. General-purpose black or gray foam tapes manufactured for use in applications requiring positive seals on irregular surfaces or when flex and conformability to seal tight radius curves are critical considerations. Easy to compress and conformable but still strong and resilient. Is self-extinguishing formulation and meets KM VS 302A. Note: Be sure surface areas are free from contamination before applying. Firm pressure is recommended to obtain good adhesive to surface contact. These are approximate values and do not constitute a ...




		Medium Density Black PVC Foam Backing: 15# per cubic foot density foam (6) These foams are designed for gasketing and vibration dampening, and for applications that require a less compressible foam to maintain a consistent gap between two surfaces. General-purpose black foam tapes manufactured for use in applications requiring positive seals on irregular surfaces or when flex and conformability required. Easy to compress and conformable but still strong and resilient. Excellent dimensional stability and a cushion against heavier loads. Foam density permits clean die cuts and fastener penetration. Withstands wear and abrasion. Note: Be sure surface areas are free from contamination before applying. Firm pressure is recommended to obtain good adhesive to surface contact. These are ...




		LX-251: High temperature masking tape LX-251 is a high temperature masking tape designed for clean removal from a variety of surfaces after exposure to oven temperatures up to 325 degrees F. for 30 minutes. Easy handling; smooth crepe backing with high strength and conformability to irregular surfaces; exceptional cornering. Provides both resistance to paint flaking and a clean well-defined paint line. Performs well in wet strip applications. Note: Be sure surface areas are free from contamination before applying LX-251. These are approximate values and do not constitute a warranty. It is the customer's responsibility to determine these products fitness for use in the intended end use application. Test data contained herein is believed to be reliable and ...




		PET (Polyester) Backing




		LX-463: Single Coated 8.0 Mil Reinforced Composite Banner Edge Tape Tape reinforces the banner edge and eliminates need for folding, sewing and adding grommets. No tear backing is coated with an aggressive acrylic adhesive that is highly resistant to water and will hold up in extreme cold, heat and humidity. Peel adhesion: 115 oz./inch LX-463 is a single coated high strength white film that eliminates the need for banner grommets. The tape reinforces the banner edge and eliminates folding, sewing and adding grommets. The aggressive acrylic adhesive is highly resistant to water and will hold up in extreme cold, heat and humidity. Note: Be sure all surface areas are free from contamination before applying LX-463. These are approximate values and do not constitute a warranty. It ...

Single Coated Tapes

LX-347(.032"): High Density Black Urethane Foam Backing: 25# per cubic foot foam density

Light Density Black and Gray PVC Foam Backing: 7#-8# per cubic foot density foams

Medium Density Black PVC Foam Backing: 15# per cubic foot density foam

LX-251: High temperature masking tape

PET (Polyester) Backing

LX-463: Single Coated 8.0 Mil Reinforced Composite Banner Edge Tape